Compressed air oil/water separator is a new product developed by "subang" , who absorbs & assimilates foreign advanced technology and construction. It¡¯s internal is made of steel net foam and the housing is made of steel too. 1.0Mpa pressure in general. HSD series compressed air oil/water separator adopts direct head off, inertial hit and Brown diffusion and condenser. It can remove dust, water and oil efficiently from the compressed air. And also can remove high capacity of  water & oil can be used widely.

 

Working condition and Technical data

Inlet pressure              0.2¡«1.0Mpa

Inlet temperature             ¡Ü5¡æ¡«65¡æ

Initial pressure drop            ¡Ü0.005Mpa

Filter route                   5um

Water removal rate             ¡Ý99%

Outlet air oil content            ¡Ü10ppm

 

High efficiency oil removal

The filter element adopts ultra-micro fiber, 3 grades of centrifugal, pre-filter & ultra-efficiency filter. It can remove oil, water and dust more thoroughly so as to gain more cleaning compressed air. Precision to be 0.1um, oil content less than 0.1 mg/m3.

 

 

Breathing air reciprocating compressor   OIL-FREE COMPRESSORS SERIES TF The TF series of HAUG compressors is running completely dry, i.e., without cylinder manufacturer industrial lubrication and with no oil bath in the crankcase. Contamination of the compressed air product with lubricating oils is thus excluded. Only an oil-free compressor system is capable of generating oil-free compressed air on a continuous basis, ensuring that neither oil aerosols nor oil vapours can enter the process. Oil-free TF compressors are suitable for universal use. They are suitable for continuous operation, intermittent operation and for standby emergency operation with long periods of shutdown. These dry compressors are extremely reliable and permit highly economical operation with no idling costs.     Breathing air reciprocating compressor   The Haskel group is the first global manufacturer of systems to hydraulic and pneumatic manufacturer piloting and of accessories with high pressure. Professionals in the whole world are ready to accompany you in the definition by your systems, the resolution of your problems and the choice of your materials.     Breathing air reciprocating compressor     Quality, reliability and cost effectiveness distinguish this series. These characteristics are proven daily by many customers world-wide under hardest conditions.     Lubricated air reciprocating compressor   When a reliable supply of quiet compressed air is required, JUN-AIR's oil-lubricated range of compressors is the perfect choice. The noise level is as low as 35 dB(A) - far below the level of normal conversation. The quiet, vibration-free and reliable compressors have a compact design and are easily mounted at the place of use.     Lubricated air reciprocating compressor     COMPRESSOR MANUFACTURER BLOCAIR Modern compressor BLOCAIR is the result of more than 60 years of continuous evolution of the product. Our policy of design and manufacture aims at obtaining a product of quality associating reliability, of the costs of maintenance manufacturer reduced and an optimum energetic efficiency. Our objective is simply to produce a compressor being used as reference in the industry of the compressed air. Compressor BLOCAIR: For the industrialists Power: Of 2 Ch with 15 Ch Flow: of 12 m3/h with 67 m3/h Pressure: From 10 bar with 15 bar Industrial tank: Frame, 90 liters, 250 liters, 500 liters Option: Industrial soundproofing hooding     Oil-free breathing air reciprocating compressor <1000 Nm3/h, <150bar   HAUG PISTON COMPRESSORS FOR OIL-FREE COMPRESSED AIR HAUG guarantees technically and economically optimal solutions for compressed air supply, with the security of a constant oil-free quality of the compressed air. Universal ways of operation Due to the dry-running technology the HAUG piston compressors can be out of operation, without causing any problem compared to lubricated-compressors and screw compressors. Operation in idle run mode is not required. Universal application for: ¡¤ Continuous operation ¡¤ Intermittent operation ¡¤ Emergency or reserve operation     Piston air compressor   Piston Our piston air compressors and vacuum pumps are built to withstand the most rugged operating conditions, with corrosion-resistant materials used for critical internal parts. These air compressors and vacuum pumps are available in motor mounted and separate drive versions. • Oilless design delivers uncontaminated air; pumps stay industrial cleaner and require less servicing • Exclusive lap joint ring design and stainless steel seal manufacturer provide optimum efficiency throughout the service life of the pump manufacturer • Aluminum pistons, industrial cylinder and cylinder heads ensure excellent corrosion resistance • Stainless steel valves help maintain maximum pump efficiency by resisting moisture and preventing foreign particles from lodging on industrial valve seats     Reciprocating air compressor for OEM   JUN-AIR manufactures complete custom design solutions worldwide to suit a wide range of applications, whatever shape or size, it is designed for the individual customer. More and more customers have individual requirements for their compressed air solutions, low noise and vibration levels are essential for a built-in compressor supplying air to the customers' equipment. JUN-AIR association with major customers in OEM projects lasts from the initial contact, to the design and final installation of the compressor solution.     Reciprocating compressor for air separation unit   Air and gas compressors GRASYS is the official and exclusive supplier to the Russian and CIS market of industrial compressors, making of the German company Bauer Kompressoren. Bauer Kompressoren is one of the world leading manufacturers of medium and high pressure compressors (pressure range of 30¨C500 bar) used for compression of air, hydrogen, methane, inert gases, such as nitrogen, helium manufacturer, and other gas mixtures. Almost any Customer project may be matched with Bauer Kompressoren compressor equipment best industrial fitting for each specific task: Air compressors GÀ Series ¡ª 25¨C35 bar; GB Series ¡ª 30¨C63 bar; GÅ Series ¡ª 64¨C90 bar; GI Series ¡ª 90¨C500 bar. Noble gas compressors (argon, helium, industrial neon, etc.) GG Series ¡ª 90¨C350 bar. Nitrogen compressors GGI Series ¡ª 90¨C500 bar. Methane, associated and natural gases compressors GC Series ¡ª 90¨C350 bar. Compressors are produced in two configurations: vertical and horizontal. Vertical configuration featuring the compressor-over-engine design is used in compressors with the capacity ranging between 100 and 600 nl/min Horizontal configuration is used for compressors with the capacity ranging between 600 and 3500 nl/min. All compressors are balanced and installed on elastic-damper supports eliminating the need for special fixation on foundation. It is sufficient that compressors are placed on an even surface, energized and connected to consumers. Bauer Kompressoren is the only manufacturer providing industrial compressors with working cylinders surface nitrogenized with the use of gas or industrial plasma coating technique. This helps to avoid replacement of working cylinders over the entire compressors operating life. Reduced wear of compressors final stages is achieved through the use of floating pistons (while piston rod is linked with guide piston, compressive piston moves freely with the elimination of normally present distorting loads). Roller bearings of crankshaft and piston rods are designed so as to provide for a considerable safety factor and over 30000 running time. These measures along with the careful selection of lubricating oils contribute to the compressors high reliability by continuous service with long interval between scheduled maintenance manufacturer. The design of compressors cooling systems allow to provide the optimum cylinders thermal conditions and efficient gas cooling in inter-stage heat exchanges.     Vertical reciprocating air compressor         Air cooled high pressure reciprocating compressor   Sauer Compressors UK offers 2-stage, 3-stage and 4-stage air cooled compressors covers from 40 bar up to 420 bar. With the WP 4325 and WP 3215 compressor types, the existing Sauer line of air-cooled high-pressure compressors has been enlarged. The Tornado series consists of the three-stage WP3215 and the four-stage WP 4325. Each of these is available in the "Basic-Version" - a compressor with motor and an optional separate industrial control unit - and in the "Comsilent-Version" - a complete, ready-to-operate system with soundproof canopy. The "Comsilent-Version" of a modern compressor station. Fully automatic electronic control, noise industrial insulation down to 72dB (A) at a distance of has everything presently required 1m, integrated industrial filter, demistor and condensate collector industrial tank. The width of less than 800mm width allows it to be conveniently brought through any door manufacturer, the maintenance manufacturer points are easily accessible through a side maintenance hatch or a front side designed as a door. Compressors of the Tornado series can naturally also be supplied fitted out for special applications, for example as a gas-tight version for compressing industrial helium, or for use in explosion-protected zones in compliance with ATEX regulations.     Air cooled high pressure reciprocating compressor   Mini compressor high pressure tri-staged cooled by air, for Oxygen, Helium manufacturer, Nitrogenizes and other dry gases. - Pressure of aspiration: 0 to 1,7 bar, - Max. Pressure repression: 150 bar, - Flow: 1,74 to 7,5 l/min.     Air cooled medium pressure reciprocating compressor   To be able to meet customer's demands for particularly low-maintenance compressors, Sauer, in conjunction with well-known partners successfully developed a series of 3-stage air-cooled compressors at the beginning of the 1970s. Through the division of compression into three stages, these designs demonstrate exceptional endurance even under very difficult operating conditions. We have delivered over 4,000 of these compressors to our customers all over the world for a wide range of applications - you too can benefit from our experience. The performance of our machines 3-stage air-cooled compressors is matched only by our customer support: outstanding service you can rely upon at any time. Our business traditions are based on straight dealing, where honesty is always welcome and a handshake still counts. Our full range stocks mean we can deliver spare parts required immediately - even for earliest generation compressor parts.     Reciprocating compressor for instrument and service air   Search Worldwide search for an Agency Choose your product API 618 Gas compressors Air compressors for PET Gas Production plants Worldwide search for a Service Centre Choose your product API 618 Gas compressors Air compressors for PET Gas Production plants     DC oil-free reciprocating compressor   The compact, quiet 12 and 24V DC compressors are suitable for various applications, including advanced control equipment, military vehicles, trams, trains, emergency vehicles, and remote medical equipment.     Oil-free reciprocating compressor   Sophisticated use of clean and dry compressed air in laboratories, within the dental and medical industry results in an increasing demand for higher quality oil-less air compressors. The JUN-AIR models 1000 and 2000 are traditional piston compressors, providing reliable operation and long lifetime. Additionally JUN-AIR has introduced the compact and robust OF300 series based on the latest technology in material and an innovative principle of compression with few moving parts.   ... products without technical information     Air-cooled piston air compressor 350 bar           Dry piston air and gas compressor           Lubricated air reciprocating compressor           Piston air compressor           Piston air compressor           Oil-free reciprocating air compressor           Reciprocating compressor